FS: Heaps of LS1/2 Parts Crane valve tool, springs,MSD leads, SnapOn, Fuel pump etc

[LX346]

WALBRO 255LPH External fuel pump kit, complete kit. Was on the car for about 1 week and then I went to a bigger setup. As new $125 ono

Snap on INFRA-RED Thermo gun, used once, like new $150

Russel -10 Hose x2 lengths at 3ft (90cm) never had fluid or fittings attached, as new $20 per length

Manley Valve springs, titanium retainers and valve locks, good for 0.600" lift, approx 400km's use then bottom end let go. Like new $300 ono

VZ LH Engine cover, brought new and still look new, $30

LS1/2 Starter Motor, was working when removed, brought a crate engine all complete, no longer needed $50

LS1 Thermostat/housing, used very good condition $20

LS2 Thermostat/housing, crate motor take off $50 ono

MSD LS1/2 Coil leads, x2 they have only been fitted on engine once but never had a spark thru them, 2" longer than standard $20 ea

LS1 Ignition lead set (all 8) very good condition $30

LS1 Ignition lead set to suit torana with extended lead at RH rear $40

LS1 PCV setup, clean and like new, the spaghetti setup $20

LS1 valve covers with coil brackets, one bracket slightly modded for a conversion car but still usable. $40

PG trans dust cover to suit Holden V8 with factory Left Hand starter motor $100, impossible to find

Custom made top gun leads 8.8mm to suit old SBC or Holden V8, only fitted on engine and run once, then changed to factory black leads, like new $50

PM or email me condamine@unwired.com.au

Michael

[TR33VV]

I'll take the LS1 leads thanks. Gimme a buzz and we can organise pick up if you like.

Trev.
0432505369

[shep]

Is the Crane Valve tool still around, can you describe it, cost.

[Smokin SS]

PM sent...

[LX346]

Is the Crane Valve tool still around, can you describe it, cost.

Still have the crane tool, you take your rockers off and bolt the compressor on, it compressors 2 valve springs at once.

Very easy to do spring changes.

I will try find a link showing a pic.

Update of whats left
WALBRO 255LPH External fuel pump kit, complete kit. Was on the car for about 1 week and then I went to a bigger setup. As new $125 ono

Crane Cams Valev spring compressor, used once to remove valves off 1 engine. Same as this http://store.summitracing.com/partdetail.asp?part=CRN%2D99472%2D1&autoview=sku $175 incl freight

Manley Valve springs, titanium retainers and valve locks, good for 0.600" lift, approx 400km's use then bottom end let go. Like new $300 ono

LS1/2 Starter Motor, was working when removed, brought a crate engine all complete, no longer needed $50

LS1 Thermostat/housing, used very good condition $20

LS2 Thermostat/housing, crate motor take off $50 ono

MSD LS1/2 Coil leads, x1 left, 2" longer than standard $20

LS1 Ignition lead set to 7 standard, 1 thats 2" longer $40

LS1 PCV setup, clean and like new, the spaghetti setup $20

LS1 valve covers with coil brackets, one bracket slightly modded for a conversion car but still usable. $40

PG trans dust cover to suit Holden V8 with factory Left Hand starter motor $100, impossible to find

Custom made top gun leads 8.8mm to suit old SBC or Holden V8, only fitted on engine and run once, then changed to factory black leads, like new $50

PM or email me condamine@unwired.com.au

[Moods]

Do you still have the Crane tool mate? Shoot me a pm if you do.

Cheers Bud.