WTB amp (WA)

[funkshen]

any amp with similar specs as below

Amplifier Specifications
Number of Channels 1 - Mono
RMS Power (4 ohms) 200 watts x 1 channel
RMS Power (2 ohms) 400 watts x 1 channel
RMS Power (1 ohm) Not Stable
Bridged RMS Power Not Bridgeable
Total RMS Power Output 400 watts
Peak Power Output 800 watts
Minimum Impedance Unbridged 2 oh

[stumps57L]

Hi mate, i have a sony one dont know if it meets your specs i ididnt read them all.

Been sitting around doing nothing $150 ono

Model : XM504Z 4/3 channel stereo power amplifier. 4 x 50w rms at 4 ohm, bridgeable with built in high/low cross over with MOSFET power supply and output stage.Features: Channel Configuration: .4 / 3 High Pass Filter (Selectable): 80Hz -12dB/oct Low Pass Filter (Selectable): 80Hz -18dB/oct Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 50W at 4 ohm (0.04% THD) Rated / THD (14.4 V 20 Hz - 20 kHz): 2 Ch x 50W + 1 Ch x 120W at 4 ohm (0.1% THD) Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 60W at 2 ohm (0.1% THD) Maximum (14.4V): 4 Ch x 100W at 4 ohm Maximum (14.4V): 2 Ch x 125W + 1 Ch x 250W at 4 ohm Maximum (14.4V): 4 Ch x 125W at 2 ohm Frequency Response: 5Hz-50kHz Sound to Noise Ratio: 100dB Total Harmonic Distortion (1kHz):... Read More

4/3 channel stereo power amplifier. 4 x 50w rms at 4 ohm, bridgeable with built in high/low cross over with MOSFET power supply and output stage.

Features:
Channel Configuration: .4 / 3
High Pass Filter (Selectable): 80Hz -12dB/oct Low Pass Filter (Selectable): 80Hz -18dB/oct
Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 50W at 4 ohm (0.04% THD)
Rated / THD (14.4 V 20 Hz - 20 kHz): 2 Ch x 50W + 1 Ch x 120W at 4 ohm (0.1% THD)
Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 60W at 2 ohm (0.1% THD)
Maximum (14.4V): 4 Ch x 100W at 4 ohm
Maximum (14.4V): 2 Ch x 125W + 1 Ch x 250W at 4 ohm
Maximum (14.4V): 4 Ch x 125W at 2 ohm
Frequency Response: 5Hz-50kHz
Sound to Noise Ratio: 100dB
Total Harmonic Distortion (1kHz): <0.008%
Input: Number of Channels: 2
Line In: Input Sensitivity (V): .3-6
Current Drain (Rated Output Power at 4 ohms): 30A
Dimensions (W x H x D in mm) Approx.: 350 x 55 x 233

Been sitting around doing nothing $150 ono

Model : XM504Z 4/3 channel stereo power amplifier. 4 x 50w rms at 4 ohm, bridgeable with built in high/low cross over with MOSFET power supply and output stage.Features: Channel Configuration: .4 / 3 High Pass Filter (Selectable): 80Hz -12dB/oct Low Pass Filter (Selectable): 80Hz -18dB/oct Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 50W at 4 ohm (0.04% THD) Rated / THD (14.4 V 20 Hz - 20 kHz): 2 Ch x 50W + 1 Ch x 120W at 4 ohm (0.1% THD) Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 60W at 2 ohm (0.1% THD) Maximum (14.4V): 4 Ch x 100W at 4 ohm Maximum (14.4V): 2 Ch x 125W + 1 Ch x 250W at 4 ohm Maximum (14.4V): 4 Ch x 125W at 2 ohm Frequency Response: 5Hz-50kHz Sound to Noise Ratio: 100dB Total Harmonic Distortion (1kHz):... Read More

4/3 channel stereo power amplifier. 4 x 50w rms at 4 ohm, bridgeable with built in high/low cross over with MOSFET power supply and output stage.

Features:
Channel Configuration: .4 / 3
High Pass Filter (Selectable): 80Hz -12dB/oct Low Pass Filter (Selectable): 80Hz -18dB/oct
Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 50W at 4 ohm (0.04% THD)
Rated / THD (14.4 V 20 Hz - 20 kHz): 2 Ch x 50W + 1 Ch x 120W at 4 ohm (0.1% THD)
Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 60W at 2 ohm (0.1% THD)
Maximum (14.4V): 4 Ch x 100W at 4 ohm
Maximum (14.4V): 2 Ch x 125W + 1 Ch x 250W at 4 ohm
Maximum (14.4V): 4 Ch x 125W at 2 ohm
Frequency Response: 5Hz-50kHz
Sound to Noise Ratio: 100dB
Total Harmonic Distortion (1kHz): <0.008%
Input: Number of Channels: 2
Line In: Input Sensitivity (V): .3-6
Current Drain (Rated Output Power at 4 ohms): 30A
Dimensions (W x H x D in mm) Approx.: 350 x 55 x 233

Been sitting around doing nothing $150 ono

Model : XM504Z 4/3 channel stereo power amplifier. 4 x 50w rms at 4 ohm, bridgeable with built in high/low cross over with MOSFET power supply and output stage.Features: Channel Configuration: .4 / 3 High Pass Filter (Selectable): 80Hz -12dB/oct Low Pass Filter (Selectable): 80Hz -18dB/oct Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 50W at 4 ohm (0.04% THD) Rated / THD (14.4 V 20 Hz - 20 kHz): 2 Ch x 50W + 1 Ch x 120W at 4 ohm (0.1% THD) Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 60W at 2 ohm (0.1% THD) Maximum (14.4V): 4 Ch x 100W at 4 ohm Maximum (14.4V): 2 Ch x 125W + 1 Ch x 250W at 4 ohm Maximum (14.4V): 4 Ch x 125W at 2 ohm Frequency Response: 5Hz-50kHz Sound to Noise Ratio: 100dB Total Harmonic Distortion (1kHz):... Read More

4/3 channel stereo power amplifier. 4 x 50w rms at 4 ohm, bridgeable with built in high/low cross over with MOSFET power supply and output stage.

Features:
Channel Configuration: .4 / 3
High Pass Filter (Selectable): 80Hz -12dB/oct Low Pass Filter (Selectable): 80Hz -18dB/oct
Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 50W at 4 ohm (0.04% THD)
Rated / THD (14.4 V 20 Hz - 20 kHz): 2 Ch x 50W + 1 Ch x 120W at 4 ohm (0.1% THD)
Rated / THD (14.4 V 20 Hz - 20 kHz): 4 Ch x 60W at 2 ohm (0.1% THD)
Maximum (14.4V): 4 Ch x 100W at 4 ohm
Maximum (14.4V): 2 Ch x 125W + 1 Ch x 250W at 4 ohm
Maximum (14.4V): 4 Ch x 125W at 2 ohm
Frequency Response: 5Hz-50kHz
Sound to Noise Ratio: 100dB
Total Harmonic Distortion (1kHz): <0.008%
Input: Number of Channels: 2
Line In: Input Sensitivity (V): .3-6
Current Drain (Rated Output Power at 4 ohms): 30A
Dimensions (W x H x D in mm) Approx.: 350 x 55 x 233

http://i51.photobucket.com/albums/f380/stumps57L/amp.jpg

[funkshen]

nice mate, pretty interested in it. but i need to make sure it wont blow my sub..dont really know much about amps, my sub is underneath my tray on the ute so i cant find out what it is, the amp that was in there before was a kicker kx400.1 which is the specs i put up. if the equal that..sure thing we'll sort something out

[stumps57L]

cool mate sorry about the massive post previously. Like i said its just sitting there doing nothing give me a PM when you know.

[KUSTOMD]

that amp will be fine mate, i used to do installs, most subs these days will handle from 350rms upwards, the sony will put out 250rms bridged, if u r worried just turn the gain right down on the amp when you install and gradually turn it up till you are happy with the bass. i dont usually have full gain on any amp so just under eg 3/4 gain for max effiency and tweak the + or - on the db and same with hz eg 40hz for low bass or 80
+ for punchier.

[funkshen]

cheers for that kustomd.

[stumps57L]

send me a PM when your keen mate and we can work something out