Xtreme Commodore Clutch Bleeder

[XtremeClutch]

"Xtreme Clutch delivers a godsend to Commodore Mechanics frustrated with messy & time consuming clutch bleeding on VT-VZ Set-ups"

We now have a Clutch Bleeding Tool which eliminates fluid residue within the Bell-housing & saves valuable time when bleeding the Clutch on your Commodore. This is a tool that can remain in-situ for the entire vehicles' life.

We now have these available in stock for $22.45 incl GST.

Please visit our website: www.xtremeclutch.com.au for further information or alternatively if you have any questions or enquiries to either PM me, post it up in this Sponsor's Forum or send an email to chris@australianclutch.com.au & I will get back to you as soon as possible.

Chris.

[Evman]

Sounds terrific and long overdue! Well done guys. Any chance of pics or a description of how it works?

:goodjob:

[XtremeClutch]

Sounds terrific and long overdue! Well done guys. Any chance of pics or a description of how it works?

:goodjob:


Yes it's been very long overdue:dancenana:

There should be a Photo of the Clutch Bleeder on the Xtreme Website: www.xtremeclutch.com.au under the products section but if not please let me know...

The Clutch Bleeder is an extension of the Line coming from the Internal Concentric Slave Cylinder, It sits just outside the top window of the Bell-housing by approx 1-2cms. It simply screws into the Cylinder eliminating the chance of dropping socket's in the Bell-housing or spilling Fluid when attempting to bleed the Clutch.

[Evman]

Thanks guys ;)

Found it and here's a direct link (http://www.xtremeclutch.com.au/page.asp?parentid=4&parent2id=25&productid=32)

[VYSHSV8]

Email Sent

Cheers
Drew

[XtremeClutch]

Email Sent

Cheers
Drew

Drew, I didn't get your email but I'll keep a lookout...



Any enquiries please email: chris@australianclutch.com.au

Chris.

[XtremeClutch]

Email Sent

Cheers
Drew

I just got your email :goodjob:

[zorro]

can you post a direct link to where this is on the website?

[EXCESSV]

can you post a direct link to where this is on the website?see this post above by Evan ash? :rofl:


Thanks guys ;)

Found it and here's a direct link (http://www.xtremeclutch.com.au/page.asp?parentid=4&parent2id=25&productid=32)

[XtremeClutch]

Thanks for the positive feedback Guys,

Please PM me for your nearest Xtreme Distributor otherwise send an email to chris@australianclutch.com.au

[XtremeClutch]

We now have more of these available in stock :yup:

[Huthy77]

Quick Question on the bleeder...

Can you fit this, without removing the bellhousing etc? i.e. Can you simply fit this as part of a normal service, or should it be done during a clutch rebuild?

[XtremeClutch]

Quick Question on the bleeder...

Can you fit this, without removing the bellhousing etc? i.e. Can you simply fit this as part of a normal service, or should it be done during a clutch rebuild?

Yes it can be used while the bell-housing is bolted up & it will protrude from the top bell-housing window to allow easier access when bleeding.

[XtremeClutch]

These are now available through any Coventry's or Motor Trader's store in either SA or WA, Simply quote part no. CSCGM011-EXTBL

[Farlig]

Are there any install guides on these?

[VZ_V8]

Fitted mine up a few weeks ago.

Bit of a tight space to work in but was simple enough, unscrew the old, screw in the new, couldn't be easier.

Good work getting something like this out there. :thumbsup:

[XtremeClutch]

Fitted mine up a few weeks ago.

Bit of a tight space to work in but was simple enough, unscrew the old, screw in the new, couldn't be easier.

Good work getting something like this out there. :thumbsup:
Thanks mate. We've had awesome feedback on the extended bleeder's they're pretty much walking out the door:wave: