WTB: 330mm HSV/PBR Front Only Brakes

[DaveHAT]

As stated I'm wondering if anyone may have FRONT ONLY rotors/calipers and brake lines from a PBR / HSV equivalent 330mm brake kit that they would like to part with?

Curved slots preferred.

PM any offers or options.

Cheers muchly. :bounce:

[mechatron]

Tiger,

Look on ebay. $799.00 for the front calipers, 330mm rotors, brake pads, braided lines etc. Check out the link:
http://cgi.ebay.com.au/330-MM-TWIN-SPOT-brake-kit-VR-to-VZ-HSV-PBR-PK1_W0QQitemZ130001176861QQihZ003QQcategoryZ29700Q QrdZ1QQcmdZViewItem

[planetdavo]

These are NOT the same kit as the PBR PK1 or HSV fronts. He says they are 330x28[U]mm rotors, which are VR-VS HSV, plus the PBR Sports red [U]standard VT calipers with adaptor brackets, not the bigger HSV proper calipers. You aren't actually getting quite what they say, which I've noticed from this seller a few times, so be careful...

[mechatron]

Thanks Davo for the advice and sorry to mislead you TigerSS - I was mislead as well

[DaveHAT]

Thanks for the replies gents, already seen those one.

As Mr Davo has pointed to the items are not quite what they seem. 28mm as opposed to 32mm for the PK1 kit. Bit if a bugger really but...........MEH !

Anyone else?? :banana:

[Senator300]

As stated I'm wondering if anyone may have FRONT ONLY rotors/calipers and brake lines from a PBR / HSV equivalent 330mm brake kit that they would like to part with?

Curved slots preferred.

PM any offers or options.

Cheers muchly. :bounce:

Tiger SS, I have a complete set of PBR big brakes. They are new and still in boxes. 330x32 slotted, with large HSV style calipar. 315x18 vented/slotted with single spot calipar. Stainess lines, pads and all brackets and hardware + instruction sheets for complete install. This kit costs upward of 2500.00+ new, im asking 1800.00. The kit will fit VT - VY,If you are not sure go to the PBR website.

[DaveHAT]

Tiger SS, I have a complete set of PBR big brakes. They are new and still in boxes. 330x32 slotted, with large HSV style calipar. 315x18 vented/slotted with single spot calipar. Stainess lines, pads and all brackets and hardware + instruction sheets for complete install. This kit costs upward of 2500.00+ new, im asking 1800.00. The kit will fit VT - VY,If you are not sure go to the PBR website.

Thanks for that Senator.

When you factor in freight from Perth the cost would go up to over $2K. Not looking to pay that much.

Thanks again though.

[Senator300]

I actually only paid $50.00 from CSV in Melbourne. This was through Australian Air freight. Depot to Depot. Took about 3 days to Perth.

[DaveHAT]

Thanks for the offers of help gents. :cheers:

Mods please close !

:closed:

[isaac c]

Tiger,

Look on ebay. $799.00 for the front calipers, 330mm rotors, brake pads, braided lines etc. Check out the link:
http://cgi.ebay.com.au/330-MM-TWIN-SPOT-brake-kit-VR-to-VZ-HSV-PBR-PK1_W0QQitemZ130001176861QQihZ003QQcategoryZ29700Q QrdZ1QQcmdZViewItem
can i offer u 400 for da right hand side caliper

[motomk]

can i offer u 400 for da right hand side caliper

The thread is 3 years old, I suspect they are now sold. Have you tried ebay or PBR. You could try
http://www.pbrperformance.com.au/performance.htm as this is the same stuff with different badging.
http://www.pbr.com.au/products/replacement/calipers.shtml
They might be able to supply one side only?