Printable View
Hi. Just wondering if anyone can point me in the direction to where i can get some new brackets for my VE SS ute hard cover. Mine have worn a bit and it is making the hard cover rattle. a photo of the brackets im talking about are here: https://imgur.com/a/0qlBu
Any ideas what these are called if i was to look at ordering them?? alternatively if anyone is selling any id be interested!
Different lids have different brackets so best going to whoever made the lid.
Thanks for the reply wonky!
Hmm im pretty sure mine is a factory holden hard cover...but i may be wrong.
Tye holden dealer wasnt able to help.
Typical dealer........ :( I've never looked closely at a factory one but on my previous SSV ute the brackets at the back of the cabin were biiiiig!! Is that the latch at the back in your pic?
I would most likely make up something myself to fix that down, it looks fairly simple.
If you are not confident, I would suggest going to an aftermarket accessory seller who sells & fits hard lids, canopy's etc.
I am sure someone in one of those shops can retrofit something,
they might even have some of the same brackets or could point you in the right direction to get what you need. :cheers:
That latch looks very similar to the one on my ute which has a slimline Holden one fitted with the lock mounted on the top as opposed to the back like the large twin hump one.
https://farm5.staticflickr.com/4627/...93c13366_b.jpg
Just having a look at it, the bracket is bolted underneath one of the tie down brackets. Can you buy new ones? I know EGR made/make the twin hump ones. No idea on the slimline ones, though I suspect it might be the same people.
https://www.ebay.com.au/b/U-Bolts/36632/bn_71614592 ???
Why not... just loosen the adjustment nuts on the top and bottom of the U bolt at the fwd and aft ends (L/H & R/H sides), and adjust the U bolt vertically down the required amount to remove the gap between the lock latch and the U bolt. Then re-tighten the nuts to lock the U bolt in the lower position. Will take same trial and error to fine tune it.Quote:
Originally Posted by MAS308
Then the rattle will be gone...
Cost nothing to adjust it, be fixed in less than 10 minutes...
Hi.
Bit if a random question!! I have a ve ss with a genuine hard cover. I've found that over the years the 'u'shaped brackets that the hard cover clips into wear out. Ie..the hard plastic wears away and causes the jard cover to be locked down and rattle during driving. Ive been using duct tape to build it back up and it works for a few months before it wears away and does the same thing.
Wondering if anyone had had the same problem and solved it another way? I can buy new brackets but kmow ill end up in the same place!!
Thanks for any advice
Without seeing the bracket, could you cut up some thin pieces of rubber & glue them with some contact adhesive?
thanks for the quick reply.
Image attached at https://www.imageupload.net/image/ute-bracket.VoxhS
https://www.imageupload.net/image/ute-bracket.VoxhS
http://www.ls1.com.au/forum/showthread.php?171056
Ah the same thread starter. Have you tried SASLS1's suggestion?
Thinking out loud...
Undo them totally and slide over loads of head shrink tubing???
Build them back up with epoxy araldite putty or the glue??? then sand it back down again...
How much are the new ones?
I merged the threads
I was in the process of merging the threads as you posted :lol:Quote:
Originally Posted by motomk
Whoa my bad, i completely forgot i posted the same years ago!! Sorry!!!!
Thanks for merging.
As for trying the move the bracket, ive done this a few times and in the end the problem becomes the same.
Quoted $300 for a new kit which id be happy with except would end up the same i suspect.
Shrink wrap is an idea...ill also try clark rubber to see if they have anything
Could be worth going & talking to the guys at Jaycar as they have some new types of shrink wrap products in there.Quote:
Originally Posted by MAS308
What I suggested earlier won't work, must be made of soft material aye!