Catch Can Install

[deano23x]

everyone is telling me to go vented cause of the blower,in the current picture i have posted from the valve next to the oil cap it then goes to the back drivers rocker cover and back passenger rocker cover! i met up with bewsa cv8 today and he advised me to block the pipe off the manifold ( the one with the hose on it behind the throttle body) and connect that hose to a vented can!

[BLACK 346]

everyone is telling me to go vented cause of the blower,in the current picture i have posted from the valve next to the oil cap it then goes to the back drivers rocker cover and back passenger rocker cover! i met up with bewsa cv8 today and he advised me to block the pipe off the manifold ( the one with the hose on it behind the throttle body) and connect that hose to a vented can!

Sounds right. The ones I have blocked are the one on the manifold, the one on the T/B and the rear one on the drivers side tappet cover. I have one hose running from the front drivers side tappet cover to the can and one running from the rear of the passenger side tappet cover to the can

[deano23x]

ok no worres cheers, guess you have a blower aswell? vented or sealed? y is your drivers side rear one blocked? cheers

[BLACK 346]

ok no worres cheers, guess you have a blower aswell? vented or sealed? y is your drivers side rear one blocked? cheers

No blower, heads and cam, wouldn't mind one though
This was how I was advised to set it up by one of the forum sponsors,
and yes it is vented.

[deano23x]

ok thank you again black 346 sounds good! if ya got a pic chuck it up please! cheers

[BLACK 346]

ok thank you again black 346 sounds good! if ya got a pic chuck it up please! cheers

Sorry don't have any pics, I am a bit slack with that sort of thing.

[deano23x]

not a problem, once again appreciate your help!

[BLACK 346]

not a problem, once again appreciate your help!

More than welcome mate

[SLugg]

anypic of an LS3 catch can istall ?

[madalpinestar]

You would still set up a catch can same as the pic below , just replace the short hose that goes from the valley cover to the intake manifold with the hoses that go to and from the catch can , leave the one that goes from the maf pipe to the rocker cover there and if you go otr plumb a hose that gets fresh filtered air from somewhere in between the throttle body and air filter .

I hope someone is able to help, its a bit confusing... i have a vy2, is this the same setup? i have a sealed elite catch can ready to be put in

[motorin on]

yes I have a VY11 and this is how I have fitted mine

I hope someone is able to help, its a bit confusing... i have a vy2, is this the same setup? i have a sealed elite catch can ready to be put in

[motorin on]

yeah this doesn't look right to me either after looking at the top photo.It looks like it just circulating the dirty air
if the can never collects oil then it isn't fitted properly,you will know after a month

Where are those hoses coming from?

Looks like the rear of the passenger rocker cover and the front of the drivers rocker cover.

Unless the VX setup is different, I thought one went into the manifold behind the TB.

Might just be a hard pic to follow

[motorin on]

I have a tip for guy's posting photos like those of catch cans.Put different colour tape or tape with numbers on the hoses so repliers can give help a lot easier

[Carlin1983]

Thought id Post here, instead of starting a new thread.

I have installed a Crate LS3 into my WL Stato, Just checking i have installed catch can right, Previous engine was a L76.

So i have go a hose from under the throttle body, into catch can, then out of catch can into side of throttle body, and i have a bung on the rocker cover passenger side. i have attached pics.

have i done it correct.

Is the PCV internal on the LS3.

[Carlin1983]

nudge.......